one male masturbator is simple to use, but some good habits allow you to obtain better sensations and above all to keep the product longer. Before first use, take the time to check the contents of the package, clean the toy and prepare a compatible lubricant.
Check the product after receipt
When opening, check the packaging and general condition of the masturbator. The material should be intact, without tearing or abnormally sticky or deformed areas. Also check that the accessories advertised on the product sheet are present.
A slight oily sensation may exist on some TPE masturbators. This material is very flexible and realistic, but its surface and composition require a suitable maintenance. A maintenance powder may also be present depending on the manufacturer.
Clean before first use
Even when a product is new, a first cleaning is recommended. Use lukewarm water and, if the manufacturer allows, a gentle sex toy cleaner. Avoid aggressive products, alcohol, bleach and highly fragrant detergents.
Gently rinse the channel. If the model is not fully open, circulate the water without pulling the entrance strongly. A sudden manipulation can enlarge or tear the finer areas.
After rinsing, gently shake the masturbator to drain off excess water. If you want to use it immediately, a few drops of residual moisture are generally not a problem, but the toy will have to be perfectly dried before storage.
Which lubricant to use?
For a TPE masturbator or when you are not familiar with the material compatibility, the simplest choice is a Water-based lubricant.
Lubricants exist in several textures: very fluid, thicker or formulated to stay slippery longer. Start with a small amount. It is easier to add then than to clean an excess.
Drop some lubricant at the entrance and into the channel. Gently squeeze the masturbator body to distribute the product. Check with a clean finger that the first inner areas are sufficiently slippery.
Avoid silicone oils and lubricants as long as the manufacturer does not confirm their compatibility with your model. Some materials may swell, soften or deteriorate on contact with unsuitable products.
Warm up the masturbator
Some models are supplied with a heating rod or accept a heating accessory. Use only a compatible system and follow its instructions.
The temperature should be warm and comfortable. Never heat a masturbator in the microwave and do not use boiling water. If using a heating rod, remove it and then test the temperature by hand before penetration.
Heating is not mandatory: you can also leave the masturbator for a few minutes in a hot room or, if the manufacturer allows it, lightly warm its surface with lukewarm water before wiping it well.
How to use it comfortably?
Sit in a stable position. With one hand, guide the masturbator's entry to the penis without forcing. Add lubricant if the penetration pulls or if the movement becomes less fluid.
Start slowly. Internal textures can be much more stimulating than they seem. Then vary the speed, depth and amplitude according to your feelings.
Closed models sometimes allow you to modify the sucking sensation by compressing the body or acting on a vent. Do it gradually: too much pressure is not necessary to obtain intense stimulation.
During the session, never force if you feel pain, pinching or numbness. Pleasant stimulation should not require any discomfort.
Clean immediately after use
Cleaning after each session is essential. The sperm and lubricant left in the canal promote odors and can accelerate material degradation.
Rinse first with lukewarm water. Then use a suitable cleaner or a very mild soap if the manufacturer's instructions allow it. Circulate the water in the canal and clean the reliefs without turning over or overstretching the masturbator.
On a one-eyed channel, a soft jet or compatible cleaning tool can help reach the bottom. Avoid sharp or rigid objects that could pierce the TPE.
Drying is as important as washing
Once rinsed, shake the masturbator and then dab the outside with a clean, lint-free towel. The interior should dry completely before storage.
Place it in a ventilated place, sheltered from sun and heat. Depending on the depth of the canal, drying can take several hours. Do not immediately close an airtight case around a still wet toy: trapped humidity promotes bad smells and molds.
When the TPE becomes sticky after washing and drying, a very thin layer of maintenance powder provided for this material can help to regain a drier touch. Do not use scented talc without checking the manufacturer's recommendations.
Put your masturbator well
Keep it clean, dry and separated from objects that may color it. Some soft materials can absorb pigments from other sex toys or very dark fabrics.
Also keep the masturbator away from sharp objects, radiators and direct sunlight. If it has a shell, put it back only when the interior is perfectly dry.
Captain – 5 suction 10 vibration simulated vaginal entry male masturbator49,99€View the product
Use and maintenance checklist
- Clean the masturbator before first use.
- Use a compatible lubricant, ideally water-based when in doubt.
- Start slowly and add lubricant if the movement is hanging.
- Rinse the product after each use according to the manufacturer's instructions.
- Let the inside dry completely before storing it.
For a beginner, the essential therefore is in four gestures: lubricate enough, start gently, clean after each use and let it dry completely. These habits improve comfort and significantly extend the product life.
Some habits that avoid problems
Wash your hands before handling the toy, especially if you need to touch the inside of the canal. Do not use the masturbator if it has a high tear, unusual smell that persists after cleaning or traces of mold. Finally, if several people use sex toys, do not share a porous masturbator without appropriate protection and without respecting the manufacturer's hygiene recommendations.
French 
English (United States) 
German 
Spanish 
Portuguese 
Italian 
English (UK)